Baosteel B Series: Reading Four Fields Off a Grade Code
A Baosteel B series grade code packs four fields into nine characters, so B35A300 already answers thickness and watt loss. That saves a datasheet lookup, and above all it prevents a costly mix-up at quotation stage. Stock sits in Wuxi, at Jiangsu Zhongtong Weiye Special Steel Co., Ltd.
The Baosteel B Series in Brief
Four fields run in a fixed order, although only one needs a table. That stock covers grain oriented electrical steel sheet for transformer cores, which we slit from 20 to 1,250 mm. First, the prefix names the mill system. Thickness then sits in hundredths of a millimetre. Next, a letter marks the product family, and a number carries loss times one hundred. Therefore a buyer reads a code left to right, and the last field sets the price.
The Four Fields of a Baosteel B Series Code
Four blocks make the code, while each one answers a different question. Read them in order, since the letter in the middle changes the third field.

Field One: The B Prefix
The leading B marks the mill grade system, rather than a product property. It tells a buyer which naming key applies, so a table lookup starts there. This means a code without that prefix belongs to another system, and its fields may run in reverse.
Field Two: Thickness in Hundredths
Two digits then give thickness in hundredths of a millimetre, so 35 means 0.35 mm. That field decides weight per square metre, since 0.35 mm runs near 2.748 kg per square metre. So a thickness field plus an area gives a tonnage.
Field Three: The Letter Segment
One letter also marks the product family. A, R, and P then lead to different reference fields. An A code covers a non oriented duty, such as a motor core. An R or P code instead covers an oriented one. Hence the letter decides which flux density the loss figure refers to.
Field Four: Loss Times One Hundred
Finally, the trailing number carries loss times one hundred, so 300 means 3.00 W/kg. A code ending in 085 then means 0.85 W/kg, which reads as a thin oriented sheet. For this reason the last field sets the magnetic price more than the first.
Three Worked Examples
Three codes then cover the common cases, and each one reads in a single pass. Compare them side by side, since the letter changes the reference field.
B35A300: 0.35 mm and 3.00 W/kg
B35A300 reads as 0.35 mm with 3.00 W/kg at 1.5 T. That sheet suits a small motor or a reactor, since cost matters more than loss. Therefore it sits at the volume end of the range.
B50A470: 0.50 mm and 4.70 W/kg
B50A470 reads as 0.50 mm with 4.70 W/kg at 1.5 T. That grade matches the GB name 50W470, which carries the same two numbers in reverse order. This means one sheet travels under two names, as a silicon steel grade conversion page explains.
B23R085: 0.23 mm and 0.85 W/kg
B23R085 reads as 0.23 mm with 0.85 W/kg at 1.7 T. That specification suits a distribution transformer core, since no-load loss sets the tariff. A 23RK085 and 27RK095 transformer core grades page covers the WISCO pair.
Which Reference Field Applies
Two reference fields appear across the series. Mixing them then ruins a comparison. An A code quotes loss at 1.5 T, for example. An R or P code instead quotes it at 1.7 T. Hence 4.70 and 0.85 sit on different bases, so the raw ratio of 5.53 means nothing. A buyer who compares them directly reaches a wrong conclusion about both sheets.
Where the Code Stops and the Certificate Starts
A code fixes four fields, but it leaves several open. Indeed, coating class, surface finish, edge condition, and width all sit outside the code. Thus a quotation should name those four extras, since a code alone does not price a coil. The certificate then carries the measured loss, which may beat the code limit. A silicon steel standards four groups page covers the document side.
B Series Against GB and EN Names
Three naming systems describe one sheet, although each one orders the fields differently. A GB code such as 50W470 puts thickness first and loss last. An EN code such as M470-50A puts loss first and thickness second. The B series brackets both with a prefix and a letter. Hence a buyer should convert before comparing, rather than after.
What Goes Wrong
One buyer reads B35A300 as 0.30 mm, since 300 looks like a thickness. Another compares B50A470 with B23R085, then wonders why one looks five times worse. A third quotes a code without a coating class, then receives a sheet it cannot anneal. Those three errors arrive monthly, and the first one changes a weight calculation by fifteen percent.
What We Do Not Do
We neither melt nor roll steel. Nor do we invent a grade code, and we never translate one code into another. Those limits keep the answer honest, so a conversion stays trustworthy.
Request a Quotation
Send the code, the width, the tonnage, and the coating class, so the reply carries a price. Those four fields then price a coil, while the fifth field sets the certificate type. An unconfirmed code goes back to you within one working day, rather than into a guess. We answer a grade enquiry in that window, so a quotation can be planned inside two weeks. The silicon steel mill grades page covers the other mill systems.
Meanwhile a non oriented electrical steel for motor stampings covers an A code duty. A CRGO silicon steel coil instead covers an R code duty.
Related Reading
First, the what are the different grades of silicon steel page covers the field layout. A silicon steel sheet weight calculation page turns thickness into tonnage. A silicon steel hub page then answers six basic questions.
Frequently Asked Questions
Loss times one hundred, so 300 means 3.00 W/kg at 1.5 T.
Yes on thickness and loss, although the fields run in a different order.
1.5 T for an A code, but 1.7 T for an R or P code.
No, since 4.70 sits at 1.5 T and 0.85 sits at 1.7 T, a different basis.
It runs from 0.20 mm to 0.65 mm, because thin gauges dominate.
No, so the coating must be named separately on the order.
Stock moves in days from Wuxi, while a mill booking usually runs in weeks.
- Email: vera.liang@ztwysteel.com
- Location: Xishan District, Wuxi, Jiangsu, China
- Supply range: CRGO and CRNGO 0.20–0.65 mm, as well as four coating classes
- Slitting: 20–1,250 mm, ±0.05 mm, so burr stays under 0.02 mm
- Documentation: MTC EN 10204 3.1 with grade, thickness and loss basis, while 3.2 comes on request
- Response time: grade enquiries answered within one working day, so quotes stay valid for two weeks