What forms are Monel alloys available in (plate, coil, strip)?

Five forms cover the range, so Monel alloys ship as coil, slit strip, plate, bar, or tube. Each form carries its own size ceiling, and each mill route stops somewhere different. Jiangsu Zhongtong Weiye Special Steel Co., Ltd. holds 401, 404, 502, K500, and R405 stock, and it quotes 400 in the form the part needs.

The Short Answer

Coil covers thin metal up to 1,250 mm wide. Plate covers the same width at 1 to 50 mm thick, while bar runs heavier. Bar runs 12 to 250 mm across, and tube serves heat transfer. Hence the part shape decides the form before the price does.

The Matrix

Form Thickness or size Width or diameter Typical length
Coil 0.5–3 mm up to 1,250 mm 3–5 t per coil
Slit strip 0.5–3 mm 20–1,250 mm coil or cut length
Plate 1–50 mm up to 1,250 mm under 4 m
Bar 12–250 mm round, square, flat under 4 m
Tube 6–50 mm wall 8–150 mm OD under 6 m

That table answers most first enquiries, since each form has a hard edge.

Coil Limits

A coil holds a 508 mm inner core, and it weighs 3 to 5 t. Width stops at the mill’s 1,250 mm maximum, because no wider roll exists for Monel. Gauge stops near 3 mm, since a heavier strip needs a plate route. Therefore, the coil capacity sets the first limit.

Strip Limits

Slitting cuts a mother coil into narrower strip, from 20 mm to the full width. Width holds ±0.05 mm, and the burr stays under 0.02 mm, so a stamped edge needs no extra filing. A stamped pin or a seal ring uses that route, since a press needs flat, even metal. Monel 401 strip covers the seal duty at 0.05 to 1 mm. Hence the strip form serves the press shop.

Plate Limits

Plate runs 1 to 50 mm thick, and a cut length stays under 4 m with ±1 mm. Squareness holds to 1 mm per metre, while a sheared edge stays clean enough for a weld prep. A tank shell or a tube sheet starts from plate, because fabrication needs a flat blank. Therefore, the plate form serves fabrication rather than stamping.

Bar Limits

Bar runs 12 to 250 mm across, in round, square, or flat section. A pump shaft or a valve stem starts from bar, since a turning centre suits a solid section. Monel K-500 bar and forging stock covers the aged duty at that size. Hence the bar form serves the machine shop.

Tube Limits

Tube runs 8 to 150 mm outside diameter, with wall from 6 to 50 mm depending on the size. A condenser uses it, while the tube sheet follows from plate. Nickel 201 tube and pipe shows the same route where copper contamination rules out Monel. Therefore, the tube form serves heat transfer.

Which Form for Which Part

Strip suits a gasket ring, since a press cannot start from bar. Plate suits a vessel shell, because a 4 m cut allows a rolled ring. Bar suits a shaft, while tube suits a condenser bundle. A large tank shell may need plate welded into a ring, since no coil reaches that width. Hence the drawing usually names the form already.

Weight and Packing

A 20-foot container takes 25 to 28 t, so a mixed order should balance forms against weight. Coils travel on a skid with edge protectors, while plate travels on a wooden pallet with a stencil. Bar ships in a bundle with a tag per heat, since a mixed bundle needs traceability. Therefore, the packing follows the form.

Monel coil, plate and bar stock grouped by supply form

The Certificate by Form

Plate and strip certify to ASTM B127, bar to B164, and tube to B165. The certificate names the UNS number, such as N04400 or N05500, plus the heat. A mixed order therefore carries several certificates, since each form has its own document. Hence the paper count follows the form count.

Where Buyers Get It Wrong

A buyer asks for a 2 m wide Monel coil, which no mill rolls. The order then stalls at the mill. Another orders plate for a stamped ring and pays for scrap in the blank. A third orders bar for a 1 mm gasket, where strip would cost less. Those three errors cover most of our returns.

What We Do Not Do

We do not melt or roll Monel. We do not forge a bar or draw a tube. Nor do we promise a coil width beyond the mill limit.

Those limits keep the form honest.

Specify Your Order

First, name the part and its shape. Second, give the thickness or the diameter. Then state the length and the quantity, so the form matches the mill route.

Related Reading

The grade naming note shows how a designation is built, so a UNS number reads against a trade name. Cut-length practice appears in the cut-to-size note.

Frequently Asked Questions

Is Monel available in coil? Yes, at 0.5 to 3 mm and up to 1,250 mm wide.

What is the largest plate? 50 mm thick and under 4 m long, cut to ±1 mm.

Can you slit strip to 20 mm? We can, at ±0.05 mm with the burr under 0.02 mm.

Do you supply Monel tube? We quote it per size, since the mill rolls tube to order.

Which form suits a pump shaft? Bar, in the aged condition for K500.

  • Email: vera.liang@ztwysteel.com
  • Location: Xishan District, Wuxi, Jiangsu, China
  • Supply range: coil 0.5–3 mm, plate 1–50 mm, bar 12–250 mm, tube on request
  • Cutting: length under 4 m, ±1 mm, squareness 1 mm per metre
  • Documentation: MTC EN 10204 3.1 with UNS number, 3.2 on request